Brainchild is the largest controller maker in the world. With good quality and competitive prices the products have been sold over 70 countries in the world. A strong and experienced R&D team is allowed us to offer customers innovative and state-of-art products all the years, It is the philosophy in pursuit of perfection through continuous improvement.

Brainchild Electronic was established in 1977. The factory has a full SMT line of automatic production and also certified ISO9001 TUV Rheinland. The CSA certified laboratory is well equipped to do CSA, UL and CE tests.

    
      FEATURES

• Portable with Modbus connectivity.
• Simple setup and easy handing
• Up to 128 Module on RS485 network
• Isolated modules available for special applications
• Low-cost IO modules addition to existing PLC system
• Standard software for module configuration and trouble shooting
• Date acquisition software for data storage and Real-time analysis on PC
• IO modules used with the third party software via Modules RTU Protocol
• Interface with field devices to provide real-time data for SCADA / PLC / HMI
• LEDs on every modules for digital IO status, communication and power supply
• Different types of IO Modules AI, AO, DI, DO,RTD, Thermocouples are available.
• Direct reading of temperature without scaling by using RTD and Themocouple   Modules

• Control/Monitor/Alarm via GSM mobile phone, no distance limitation. User can    control/monitor/alarm their devices all over the world.
• 8 channels Analog input (4 -20 mA)
• 8 Relay outputs 8 Switch inputs, normal open, close alarm
• 8 Analog inputs: system can preset 4 mA and 20 mA input value according the real   measuring value and setting display unit. It can read actual measuring data via the   SMS ( Short Message) requested, such as CH1= 28.0 C. CH2=53.7 %RH, CH3=7.01   pH CH8= 230.5 Enable or disable Analog input alarm (High alarm, Low alarm)via SMS.
• Enable or disable switch Input alarm (close alarm ) via SMS.
• Set relay output On/Off via SMS
• Dot matrix LCD display show Analog input value, Switch input and Relay output    status.
• All setting value will be saved into EPROM IC, no loss.
• Mobile telephone can call out all channel measuring value, status of Switch input and    Relay output at any time.
• Can default two telephone no., alarm SMS can be sent to two users.
• Build GSM mobile modem (dual band ).
• After the SMS command sent by mobile phone,the confirm message will be sent back    to the mobile, safe and no loss. 
• Intelligent application , innovation, wide range, no limitation

PC software used to connect with IO Modules via RS485/RS232 converter for Data acquisition purpose. Maximum 1024 tags are supported. All the data from the IO Modules can be collected and stored in PC as preconfigured sample rates. Real-Time Viewer is available to display real-time data in digital values, bar graphs, Trends etc. Historical Viewer is available too,DDE features can
make real-time data used for the third party application like Excel. Alarm management is allowed the user can configure it in maximum four different events from six possible types as high, Low, high high, low low,rate of increase, rate of decrease. Alarming email can be received via internet. 200 pages of displays are available, and each page displays maximum 6 tags.

PD1000 power transducer is Ethernet-enabled revenue class multifunction meter for power measurement, power quality analysis, power usage.

PD1000 is designed for continuous monitoring of 3 phase system. All essential power parameters including current, voltage, power, active and reactive energy are integrated in a single meter. lts bi-directional energy measurement and harmonic analysis function makes PD1000 suitable for modern industrial power management. The built-in Ethernet
and rich communication abilities enables PD 1000 to be easily connected with most modern third-party SCADA system

The Power Manager is used to integrate the power system in factory or building Via the electricity transducers. The user can use it to remotely monitor & control the demand for electricity consumption in efficient & cost effective way.

• Widely used for power monitoring and control in factory and building.
• Manage Up to 16 units of electricity transducers.
• Communication interface, CANBus Ethernet or RS485
• Communication protocol DeviceNet or ModBus
• Integrate with Factory and building control system
• Remote data monitoring and Control via Internet
• Electricity demand control
• Multi-tariff management with TOU (Time- Of-use rate)
• Built-in web server and FTP server for remote monitoring,
  control & Data download
• Automatic sending report and alarm status by e-mail
• Front USB Host port used with flash drive, mouse or Keyboard.